SOLVED I can't restore the functionality of the Brcm Internet module

[AnnaMarua]

Hello fellow hackers. The problem is with my BCM94360CS2 broadcom, I followed this guide:

GUIDE - How to Fix Broadcom WiFi on macOS Sonoma and Later

How to Fix Broadcom WiFi on macOS Sonoma and Later This guide covers fixing Broadcom WiFi on macOS Sonoma and Later using Clover and OpenCore. By following this guide, you'll be able to enable Broadcom based WiFi on macOS Sonoma and Later using Clover or OpenCore Bootloader. This guide is...

elitemacx86.com

However, nothing helps, the SIP is disabled, the security module is also disabled, the system was patched with the latest OCLP 1.5.0, after the patch only Bluetooth is launched, the Internet also continues to remain dead

Of all the Kexts, I have only the AirPortBrcmNic injector disabled, since it calls Daemon 'PXSX' (I'll attach a screenshot below) and even with the presence of an injector, nothing works
Please help me, I'm sure it can be started, but I don't understand how, I've been puzzling over this for the third day, and yes, the moudle is definitely working, since I upgraded to sonoma from ventura
I have attached files below that may help

Opencore version 1.0.0
OCLP 1.5.0
Kexts are all the latest version
all screenshots were taken on mac OS version 14.5 after the system patch
The BCM94360CS2 Wi-Fi module itself is removed from the original MacBook and connected to my laptop via an NGFF M.2 adapter


I will provide additional files if necessary





UPDATE:

in general, the update, I was able to launch my Internet, As the administrator said earlier, I need to download from the Skywalk acidantera github

SOLVED - I can't restore the functionality of the Brcm Internet module

Also attach PCI Device info from Hackintool! here. Everything you asked for is in the archive

elitemacx86.com

as well as the problem turned out to be one error made in blocking the kernel

it was written in my config:

com.apple.iokit.IOSkyWalkFamily

But it should be:

com.apple.iokit.IOSkywalkFamily

As a result, opencore did not block the kexts located in the SLE, as a result, it caused a kernel error due to the fact that two cupcakes conflicted with each other, after correcting the letters in the kernel lock, the system successfully booted and identified my Internet module

 

[EliteMacx86]

Hello fellow hackers. The problem is with my BCM94360CS2 broadcom, I followed this guide:

GUIDE - How to Fix Broadcom WiFi on macOS Sonoma and Later

How to Fix Broadcom WiFi on macOS Sonoma and Later This guide covers fixing Broadcom WiFi on macOS Sonoma and Later using Clover and OpenCore. By following this guide, you'll be able to enable Broadcom based WiFi on macOS Sonoma and Later using Clover or OpenCore Bootloader. This guide is...

elitemacx86.com

However, nothing helps, the SIP is disabled, the security module is also disabled, the system was patched with the latest OCLP 1.5.0, after the patch only Bluetooth is launched, the Internet also continues to remain dead

Of all the Kexts, I have only the AirPortBrcmNic injector disabled, since it calls Daemon 'PXSX' (I'll attach a screenshot below) and even with the presence of an injector, nothing works
Please help me, I'm sure it can be started, but I don't understand how, I've been puzzling over this for the third day, and yes, the moudle is definitely working, since I upgraded to sonoma from ventura
I have attached files below that may help

Opencore version 1.0.0
OCLP 1.5.0
Kexts are all the latest version
all screenshots were taken on mac OS version 14.5 after the system patch
The BCM94360CS2 Wi-Fi module itself is removed from the original MacBook and connected to my laptop via an NGFF M.2 adapter


I will provide additional files if necessary

Does the system get stuck during boot or it boots fine and the WiFi doesn't work?

 

[AnnaMarua]

Does the system get stuck during boot or it boots fine and the WiFi doesn't work?

Does the system get stuck during boot or it boots fine and the WiFi doesn't work?

If you add an AirPortBrcmNic injector, then the system takes a very long time to load by sending me Daemon 'PXSX', eventually it starts, but there is no Internet, and legacy pater does not offer to patch the system, if you do everything without an injector, legacy patcher sees the module and prompts me to patch it, after which Bluetooth starts and only, i.e. the Internet is just No

 

[EliteMacx86]

If you add an AirPortBrcmNic injector, then the system takes a very long time to load by sending me Daemon 'PXSX', eventually it starts, but there is no Internet, and legacy pater does not offer to patch the system, if you do everything without an injector, legacy patcher sees the module and prompts me to patch it, after which Bluetooth starts and only, i.e. the Internet is just No

So, eventually, you can boot, just no internet. Is that correct?

 

[AnnaMarua]

So, eventually, you can boot, just no internet. Is that correct?

Yes, the system is booting but there is no internet connection

 

[EliteMacx86]

Yes, the system is booting but there is no internet connection

Attach the complete EFI+System Report+IOReg.

 

[AnnaMarua]

Attach the complete EFI+System Report+IOReg.

Where can I get a system report? efi and IOReg are attached below

 

[EliteMacx86]

Where can I get a system report? efi and IOReg are attached below

Apple logo>About This Mac>System Report>File>Save

 

[AnnaMarua]

Apple logo>About This Mac>System Report>File>Save

here I attach a file with efi, IOReg and a report on the system

 

[EliteMacx86]

here I attach a file with efi, IOReg and a report on the system

Also attach PCI Device info from Hackintool!